Waypoints - from 10 - 70. On average 20 Distance - average 70-100 miles
The "out / in" zoom appears instantly no matter how long been navigating. Zoom works 100% in all conditions.
The Toolbar is the problem. I noticed that the Toolbar response gets worse the longer your ride and how hard the app works ie high number of recalculations especially after missing a waypoint.
At the beginning of the navigation the Toolbar appears normally (usually within a second after the tap - "out / in" zoom appears first and then the Toolbar. After an hour things go really bad and the Toolbar appears less and less. This happens whether you have waypoints or not.
I noticed but could be wrong that if I stop and tap the screen the Toolbar appears - possibly Navigator is in an idle mode ie no calculations.
The video actually was made on my way back, no waypoints just the destination, and just 6-7 miles from home.
On your next ride please tap the screen and see what happens - you will know the tap is accepted as the Zoom will appear at all times - is the Toolbar we are chasing... At the beginning will be fine but later on it deteriorates. It’s very random and I cannot work out the pattern but for sure the harder or longer Mapfactor works the worse it gets.
I am sure its not my device as I had the same issue with a Samsung and a Blackberry. The phone now is a Sony xz2 which is quite fast (and waterproof – important - on a motorbike in UK :) )
MacDony, Slight confusion. I am referring to the + / - zoom in/out buttons that appear when you tap the screen when in navigation or map mode. A different Toolbar appears based on the mode.
I don't think the settings have anything to do with this and you will still be able to test without changing your settings.
Thanks for testing. I presume this was a short ride. I counted 5 fails at the end of the navigation. Noticed that at the beginning the toolbar will pop up without the +/- button appearing first. Also noticed that the fails happened at the time of a calculation.
I get the toolbar appearing at the beginning of the navigation but it gets worse after some time.
If you don't mind try it after an hour or so of navigating. I am convinced the harder and longer the app works the worse it gets.
Really appreciate this and hope a solution is found soon.
Tested for around 40 miles / 1:20 h ride. It performed better than ever before. Most of the times the response was quick and with just one tap. There were a few times that it required a second tap and a couple of times 3-4 taps - most of the misses were after the half hour. A miss is when only the +/- zoom buttons appear but not the toolbar.
You must be on the right track. I will test it again during the weekend with a longer ride.
Hope more will give it a test. Nothing to change on their settings just tap the screen and look for the toolbar to appear from the bottom - not just the +/- buttons. Test it on long navigations.
Unfortunately on the second ride last Sunday the response was not good.
More misses than hits. I was looking for a pattern to narrow down the problem but there are too many areas to look at but I noticed the following that could be something to look into more carefully
On "screen tap" one of these 3 things will happen.
1. The +/- zoom buttons appear. This happens most of the time 2. The +/- zoom buttons appear and then the toolbar. This happens some of the time 3. The toolbar appears. This is not very common
It seems the screen tap activates 2 functions and possibly this could be the main problem. I know that every "screen tap" is ok as I have on the "show taps" on my phone.
Some suggestions.
1. As one off test version just for this issue. Remove the Zoom +/- function and let me test it with only the Toolbar function available to the screen tap.
If 1 solves the problem possibly 2 or 3 could be a final solution.
2. Add an option to display the Toolbar on the screen at all times. Show less panels and possibly a bit smaller. There is enough room for it.
3. Divide screen into two screen tap areas. Top half for the Toolbar and bottom half for the zoom.
Decided to switch over to 3D screen mode and I noticed that the waypoint labels are not displayed.
On 2D mode waypoints labels sometimes appear subject to the number of characters and where the waypoint appears on the screen BUT at least I can see a label now and then.
On 3D mode seems that the labels never appear irrespective of the number of characters or screen location.
I seem to be getting nowhere with the Waypoint issues - toolbar and waypoint labels are very important to me.
81 crash every day. Something seems to be wrong with it. And when more than 3h gps recording it crash. And it say always after such a crash "Prüfung der Daten auf Schäden (Checking the data for damage)" and "Alle Daten sind in Ordnung (Data is in order)" after finish this senseless testing.
Hi, My Phone: Version 5.5.81 arm64-v8a My old phone: Version 5.5.81 armeabi-v7a Not possible to restore my favorites or settings from Drive on my old smartphone. I can choose the backup, select the files to import, but nothing applies.
Thank you Matthias, but Navigator has the function of backup and restore. it must work normally because if I lose my new phone, I want to recover all my favorites and settings from Navigator. If this function is no longer valid, the developers must signal it.
The crash on exit problem seems to be fixed in 81. I closed the Software after ca. 3h GPS Recording every day and it crashed no time. It seems this problem is fixed in 81.